| |
| | |
喷雾特性及用途：
该喷嘴结构新颖，雾化均匀，其喷淋形式为矩形，
其有流量大、喷射角大、不易堵塞的特点；主要使用于
新型的喷淋结晶器，对钢坯进行强行冷却，也可用于清
洗，植物喷灌等。
| | | 技术参数表： |
|
|
产品型号 | 国外相应型号 |
MPa压力下的流量（1/min） |
0.3Mpa时（长径）
喷射角（度） | |
0.1 | 0.2 |
0.3 | 0.4 |
0.5 | | 1/2"PZ5095×45J | Hpb59-
11Cr1
8Ni9Ti | 2.9 | 4.1 | 5.0 | 5.8 | 6.5 | 95×45 |
| 1/2"PZ10095×45J | 5.8 | 8.2 | 10.0 | 11.5 | 12.9 | 95×45 |
| 1/2"PZ15095×45J | 8.7 | 12.2 | 15.0 | 17.3 | 19.4 | 95×45 |
| 1/2"PZ20095×45J | 11.5 | 19.3 | 20.0 | 23.1 | 25.8 | 95×45 |
| 1/2"PZ25090×45J | 14.4 | 20.4 | 25.0 | 28.9 | 32.3 | 95×45 |
| 1/2"PZ30095×45J | 17.3 | 24.5 | 30.0 | 34.6 | 38.7 | 95×45 |
| 1/2"PZ10095×50J | 5.8 | 8.2 | 10.0 | 11.5 | 12.9 | 95×50 |
| 1/2"PZ15095×50J | 8.7 | 12.2 | 15.0 | 17.3 | 19.4 | 95×50 |
| 1/2"PZ20095×50J | 11.5 | 16.3 | 20.0 | 23.1 | 25.8 | 95×50 |
| 1/2"PZ25095×50J | 14.4 | 20.4 | 25.0 | 28.9 | 32.3 | 95×50 |
| 1/2"PZ30095×50J | 17.3 | 24.5 | 30.0 | 34.6 | 38.7 | 95×50 |
| 1/2"PZ35095×50J | 20.2 | 28.6 | 35.0 | 40.4 | 45.2 | 95×50 |
| 1/2"PZ40095×50J | 23.1 | 32.7 | 40.0 | 46.2 | 51.6 | 95×50 |
| 1/2"PZ1001051×60J | 5.8 | 8.2 | 10.0 | 11.5 | 12.9 | 105×60 |
| 1/2"PZ150105×60J | 8.7 | 12.2 | 15.0 | 17.3 | 19.4 | 105×60 |
| 1/2"PZ200105×60J | 11.5 | 16.3 | 20.0 | 23.1 | 25.8 | 105×60 |
| 1/2"PZ250105×60J | 14.4 | 20.4 | 25.0 | 28.9 | 32.3 | 105×60 |
| 1/2"PZ300105×60J | 17.3 | 24.5 | 30.0 | 34.6 | 38.7 | 105×60 |
| 1/2"PZ350105×60J | 20.2 | 28.6 | 35.0 | 40.4 | 45.2 | 105×60 |
| 1/2"PZ400105×60J | 23.1 | 32.7 | 40.0 | 46.2 | 51.6 | 105×60 |
| 1/2"PZ100110×50J | 5.8 | 8.2 | 10.0 | 11.5 | 12.9 | 110×50 |
| 1/2"PZ150110×50J | 8.7 | 12.2 | 15.0 | 17.3 | 19.4 | 110×50 |
| 1/2"PZ200110×50J | 11.5 | 16.3 | 20.0 | 23.1 | 25.8 | 110×50 |
| 1/2"PZ250110×50J | 14.4 | 20.4 | 25.0 | 28.9 | 32.3 | 110×50 |
| 1/2"PZ300110×50J | 17.3 | 24.5 | 30.0 | 34.6 | 38.7 | 110×50 |
| 1/2"PZ350110×50J | 20.2 | 28.6 | 35.0 | 40.4 | 45.2 | 110×50 |
| 1/2"PZ400110×50J | 23.1 | 32.7 | 40.0 | 46.2 | 51.6 | 110×50 |
| |
